Model NO.: Electricity Power Plant Biogas Generator
Warranty: One Year
Cooling Mode: Water Cooler
Gas Mixing Type: Outside
Technology Support: Lifetime
Phase: 3 Phase, 4wire
Rated Voltage: 400V/230V
Alternative: Siemens/Stamford/Leory Somer
Trademark: LVHUAN
Transport Package: with Standard Package
Specification: composition: methane
Origin: Shandong, China
HS Code: 85022000
The advantages of our product:
· Manufacturer with 20 years of experience
· Capacity range: 10-600KW
· Eco-friendly and clean energy solution
· Optional control panel for flexible use
· High power output and maximum efficiency
· Low operational cost, dual supply of electricity and thermal power, low maintenance expenses
· Powered by renowned gas engines and alternators
· Stable, reliable, and easy to service

Biogas Generator Set Images:
Choose from a wide variety of models
Electricity Power Plant Biogas Generator

Requirements for Biogas Genset:

Within 1m of the intake valve of the gas generator set
1) Gas temperature ≤ 40ºC
2) Pressure 3-20kpa, pressure change rate ≤ 1kpa/min
3) H2S ≤ 200mg/Nm3
4) Impurity particle size ≤ 5μm, impurity content ≤ 30mg/Nm3
5) Moisture content ≤ 40g/Nm3
6) CH4content ≥ 40%, change rate ≤ 2%/min

Parameters of Biogas Generator Set:
Model No. LU-300GFZ Voltage Transient State Regulation Rate ≤±10%
Engine No. 6190ZLDT-2 Voltage Setting Time ≤1s
Rated Power 300kw Voltage Volatility ≤±0.5%
Prime Power 240kw Frequency Transient State Regulation Rate ≤±10%
Rated Voltage 400V/230V Frequency Recovery Time ≤3s
Phase 3 phase, 4 wire Frequency Volatility ≤0.5%
Rated Speed 1000r/min Voltage Setting Range 95-105%
Rated Frequency 50Hz Heat Consumption ≤10mj/kw.h
Rated Current 1080A Lubricant Consumption 1.0-1.63g/kw.h
Voltage Steady State Regulation Rate ≤±2% Pressure 3-20kpa
 
Cylinders Number 6 Voltage Regulation Mode automatic
Cylinders Diameter 190mm Speed Regulation Mode electronic speed regulate
Stroke 210mm Lubricating Mode pressure and splash
Starting mode 24V electric motor Cooling Mode water cooler
Overhaul Time ≥30000h Exhaust Temperature ≤650ºC
Noise ≤105dB(A) Displacement 36L
Intake Mode supercharging, inter cooler Size 3000×1970×2735mm
Sparking Mode spark plug Weight 8000kg

Factory Overview:
Electricity Power Plant Biogas Generator
Electricity Power Plant Biogas Generator
Certification:
Electricity Power Plant Biogas Generator
Overseas Installation:
Electricity Power Plant Biogas Generator
Exhaust Heat Recovery System:
Working Principle: The water absorbs heat from the exhaust gas through the needle tubing in the recovery device. This tubing is fixed in the exhaust gas recovery device, conducting the heat. As a result, the water temperature can reach 50-90°C or become saturated steam under certain pressure.
 
Normally, the heat from the exhaust gas accounts for 32% of the total heat. With this system, thermal efficiency can be improved by 20-30%.
Applications:
1) Heating and bathing
2) Warming anaerobic tanks to increase gas production
3) Drying starch
4) Producing steam
5) Reducing workshop and office air temperatures using air conditioners

Silent Canopy Series:
Container generator sets are low-noise units designed according to environmental protection requirements. We use advanced noise reduction techniques and new sound-absorbing materials. They are suitable for narrow spaces or areas with strict noise regulations, such as factories, hotels, restaurants, schools, hospitals, and residential areas.
1) Common low-noise function, common noise within 75dB(A) (at 7m); super low noise within 70dB(A) (at 7m)
2) The oil tank, battery, and muffler of the unit are assembled together, making it easier to transport and install.
3) We have installed a glass window and an emergency button to make operation and monitoring easier.
Electricity Power Plant Biogas Generator

Notes on Power Plant Construction:
1) Generator rooms are usually constructed in open or semi-open types. The floor should be easy to clean and not prone to sparking.
2) If constructing a closed generator room, a single-story building must be built. Doors and windows should open outward. Install large-capacity displacement devices to prevent gas accumulation.
3) The generator room and operating room must be separated and not directly connected. Observation windows should have double-layered glass protected by steel mesh.
4) Lightning arresters are necessary.
5) Prepare enough fire extinguishing equipment.
6) The "No Fire" sign should be clearly visible. Open flames are not allowed in the generator room.
7) Combustible gases are present in the exhaust. Therefore, the exhaust pipe must be led outside the room and tightly connected.

Requirements for Equipment in the Generator Room:
1) Electrical equipment in the generator room must be explosion-proof. Turn off the power when repairing equipment.
2) Install an emergency valve at the gas pipe entry point. It can cut off the gas quickly in an emergency and should be close to the operating room.
3) A gas detection alarm system is necessary to detect leaks promptly.

Requirements for Gas Pipes:
1) All gas pipes should use seamless steel tubes. The pipe walls should not be too thin, and connections should be tightly sealed. After installation, check for leaks using a gas detector or soap solution.
2) Regularly check valves to ensure no leaks or damage.

FAQ:
1. How to choose the right model?
To select the appropriate model, we need to know the required continuous output power, local voltage and frequency, and fuel type (such as diesel, natural gas, biogas, biomass gas, coal gas, syngas, etc.). For biomass power plants and coal gas power plants, some clients may not have a gasification system, so we need information about the raw material.
 
2. What is the warranty period?
The warranty is one year. We will provide free service and spare parts during the warranty period. Lifetime service is available from our trusted after-sales team.
 
3. How to perform maintenance?
Our technicians will provide operator training. After training, local operators can perform basic maintenance based on our maintenance manual.
 
4. Is operation training offered?
Yes, operation training will be conducted by our technicians during commissioning or factory training sessions in China.
 
5. What about installation and commissioning?
Installation and commissioning of the genset will be guided by our technicians on-site.

Service Committee:
1. Pre-sale Service:
1) Our engineers will visit the site free of charge for initial assessment.
2) Based on the site conditions, we will provide design drawings such as power plant layout, cooling system diagrams, generator foundation plans, and control room designs.
 
2. Sale Service:
1) Operator training will be conducted by Lvhuan technicians during commissioning or factory training in China.
2) Installation and commissioning of the genset will be guided by Lvhuan technicians on-site.
After-Sale Service:
·Free service for quality issues during the warranty period.
·One-year warranty and lifetime service.
·We will respond within 4 hours of receiving your service request, and our staff will depart from the factory within 4 hours.

Furnishings Jacquard Fabric Machine

All the electronic jacquard machines under furnishings jacquard fabric machine classification could weave various of patterns on furnishing fabric stably and sufficiently. These jacquard looms are applicable to various of textile weaving looms, such as rapier loom, air jet loom, water jet loom, shuttle loom, projectile loom with any reed width. These digital jacquard machines are compatible with most brand of textile weaving machinery, just like just like ITEMA, SOMET, SMIT, PICANOL, DONIER, RIFA, TOYOTA, TSUDAKMOA etc.

Furnishings Jacquard Fabric Machine,Jacquard Weaving Machine,Jacquard Loom Machine,Digital Jacquard Loom

JIANGSU S&S INTELLIGENT SCIENCE AND TECHNOLOGY CO., LTD , https://www.ssjacquard.com